I2c jobs

Circuit conditioner for force sensor. This is a 2 part project, I need a simple PCB desgined as well as a arduino programming. The PCB will be enclosed in a billet aluminum case that I will make myself. Arduino; It will use a 128x64 OLED Display with I2C and 3 push buttons for user setting. Push button are Up, Down, Menu/OK. The arduino will feed 5v to the force sensor and read the analog voltage coming back. There is 6 setting to be set by user; - Resting voltage reset --> Set the voltage of the force sensor with no forward or reverse force applied - Pull Force --> Set the voltage when force sensor is being pulled - Pull Force Deadband --> Set the deadband of the pull force - Push Force --> Set the voltage when force sensor is being pushed - Push Force Deadband --> ...

Build code to Read 4 Analog Signals 4-20ma in a ESP32. We have made a board thats basicly has: ESP32 WROOM ADS1115 over i2c 4 Current to Voltage converters 4-20mA to 0-3V We would like to read the values from the probes. Actualy we've got already made code for reading and readings can be made. We apply already have a Int[] for multiples readings, made an average of squared values, Calculate the RMS value and Apply a rolling average. Althought the results still fluctuate a lot. Experience is needed. Full code can be provided.

Sensor program for Arduino with pressure sensors Bmp280 (10 units) code 1 or , hx710b (10 units) code 2 Functionality: - Detect and read temperature changes, pressure values of 10 sensors( hx710b) having same i2c address by single Arduino - Store the collected data in specific format Requirements: - Experience in programming Arduino - Knowledge of pressure sensors - Ability to read and store data at a frequency of 10Hz

Circuit #1) The goal is to have a circuit to give/cut power (+3.3v / +5v) to sub ICs/sensors, command by a microcontroller pin. Must cut the input voltage (circuit must be placed between VCC and IC) = high-side switch. Circuit #2) The goal is to have a circuit to enable/cut I2C bus (+3.3v / +5v), command by a microcontroller pin. We want +3.3v and +5v sensors to be connected on the same I2C bus - what about pull-up resistor ? Remarks: If power is cut (by circuit #1), power must not leak through I2C pull-up resistors. Maybe circuit #2 is not necessary if we can be sure that no current leak through pull-up resistors when cut the power. Guidelines : - Simplest as possible (the less or cheaper components) - Easy to find component (AliExpress, Mouser, ...) - Easy to ha...

Arduino should interpret keyboard input and transmit Morse code to the I2C which is a 20x4 display with the address of 0x20. It is by DFROBOT. Only bid if you have experience with Morse Codes. More details will be discussed in the chat.

Arduino should interpret keyboard input and transmit Morse code to the I2C which is a 20x4 display with the address of 0x20. It is by DFROBOT. Only bid if you have experience with Morse Codes. More details will be discussed in the chat.

I am looking for a midle...- Experience in firmware development - Intermediate level of experience in firmware development - Familiarity with Raspberry Pi hardware platform Ideal Skills and Experience: - Strong understanding of Python and experience in firmware development in RaspBerryPi - Able to understand PCB schematics and develop interfaces for microcontroller components - Proven experience with firmware involving I2C components, GPIO and sensors - Must have knowledge on REST API for IOT integration, and message brokers like MQTT - Ability to work independently and solve complex firmware issues - Strong troubleshooting and debugging skills If you have the required skills and experience, please submit your proposal along with relevant examples of previous firmware development...

I need an Arduino MQTT logger that will read, process, and send data to an MQTT server. The logger will be recording 4-20mA signal sensor data. The frequency at which the logger will record data will vary, allowing for a variable data rate. Other Peripherials are available as (current consumption, temperature sensor I2C, EEPROM I2C, RTC I2C, I/O Expander I2C mainly). If there is no connection to the internet. Sensor log is stored in eeprom. While back online, send data queue packets. Arduino UNO + Ethernet Shield 2 + custom board for peripherals --> connected to ethernet to obtain internet (No wifi) Connect to Hive MQTT Broker online. Skills and experience required for this project: - Proficiency in Arduino programming - Knowledge of MQTT protocol and serv...

I am looking for an experienced freelancer to design a Peltier driver circuit for my project. The circuit should meet the following requirements: - Input Voltage for the board is 24V. - Using DAC to adjust the Peltier voltage and ADC to read the Voltage/Current of Peltier [I2C or SPI]. - All the interface with uC should be isolated. [Only schematic is required WITHOUT PCB layout] Skills and Experience: - Good knowledge and experience in circuit design and electronics. - Familiarity with Peltier driver circuits and their specifications. - Attention to detail to ensure the circuit meets the desired requirements. - Ability to provide clear documentation and instructions for the circuit design. If you have the necessary skills and experience, please submit your proposal with examples...

I need someone with good experience in STM32 programming to help me build a project. I have experience with Arduino, but I am very new to STM32. This project requires I2C, UART, and recording data to the computer (optional Opamp, Ethernet port, etc.) The board I am using is Nucleo-h723ZG If you have experience with STM32 it is too ez jobs. We can work through email or Zoom, I can use English and Vietnamese.

...and high-quality solutions. - Leverage SPICE simulation tools to validate and fine-tune analog circuit designs. - Oversee the integration of microcontrollers, ensuring proficient coding in Embedded C/C++, and the ability to decipher intricate code in complex projects. - Exhibit expertise in interfacing microcontrollers with external peripherals through standard interfaces such as SPI, UART, and I2C. - Employ electronics CAD software (Eagle/Fusion360 or Altium) to create detailed and accurate schematics and layouts. - Lead prototyping efforts, taking ideas from conceptualization through to the creation of simplified demonstration devices. - Possess experience in PC-to-device communication, using languages like Python, C/C++, or JavaScript to establish Virtual COM Port (VCP) connec...

...to other ideas where and how to train the models) 2- Install the requirements python packages on the Jetson Nano. 3- testing: identify the objects from prepare pictures 4- Object detection in real time. 10 fps. The work requires good English communication skills, knowledge of image classification and recognition using Python, experience with Jetson Nano, interfacing with Jetson Nano pinout & I2C. I think this can take only few hours for someone who has the right knowledge of all the parts. The below is required: 1- Experience with Visual Studio code & python is a must. 2- Have access to Jetson Nano B01. Please don't answer if you have no access to Jetson Nano. 3- Done projects with Jetson Nano B01 If you write back - please state that you have access and experie...

I am looking for a skilled developer who can help me with porting C driver code to an STM32 microcontroller. the code is simply setting and controlling tuner chip via i2c. Current Platform: - The C driver code is currently running on a platform other than Windows or Linux. the SDK wrote for satellite receiver in plain C. Microcontroller Model: - The code needs to be ported to the STM32F series microcontroller with HAL library. Specific Requirements: - i will provide SDK and C source codes. Ideal Skills and Experience: - Strong experience in C programming - Expertise in working with STM32 microcontrollers - Familiarity with driver code porting - Ability to understand and implement specific requirements If you have the required skills and experience, please reach out to dis...

...in a low-power/sleep mode, waking at 1 second intervals to communicate with the GATT client and service any commands/tasks. Top Level Functionality List --------------------------------- The corridor light button's functionalities include: - Monitor status of a button (momentary switch, SPST-NO) via digital input - Monitor device battery life via ADC input - Interface with an LED driver (PWM or I2C) to control 4 LEDs (RGBY) - Interface with an NFC reader to read NFC card ID in device proximity for a defined time interval after a button press event. - Interface with an E-Paper Display (EPD) to display patient information - Communicate via BLE as a GATT server (custom profile) with gateway (GATT client) with the following services: - LED Service - set color/brightne...

...advanced level projects. The project involves the following requirements: - Communication Interfaces: The project requires the use of communication interfaces such as UART, SPI, and I2C. - Specific Hardware Component: The client has a specific hardware component in mind to communicate with the Arduino Mega. - Advanced Complexity: The project is of advanced complexity, requiring expertise and experience in handling complex Arduino Mega projects. Ideal Skills and Experience: - Proficiency in Arduino Mega programming and development. - Strong knowledge and experience with communication interfaces such as UART, SPI, and I2C. - Familiarity with the specific hardware component chosen by the client. - Ability to handle advanced level projects and troubleshoot complex issues. -...

I am looking for an expert freelancer who can help me with my project of interfacing Nuvoton MS51FB9AE with ADXL345 using I2C. The main purpose of this project is to perform sensor data analysis. Requirements: - The freelancer should be able to work with Nuvoton MS51FB9AE and ADXL345. - The data format can be in any readable format, so there are no specific requirements in this regard. - The freelancer should have expert level experience in handling projects like this.

...Description: - reading a UART protocol on UART2 - converting in (selectable): MAVLink Manual_Control messages, PPM and CRSF - sending the converted messages via (selectable) UART1 or Ethernet Low Level Description: - Dual Core use: Core_0 for Web-Server; Core_1 for Parsing RT-Tasks - Web server for configuration and monitoring using UI framework; either via Ethernet or WiFi or BT (selectable) - use I2C to: drive a LED bar; to read INA3221 variables - Arduino IDE with FreeRTOS - OTA updates Coder Requirements: - Good knowledge in MAVLink, PPM and CRSF (TBS Crossfire or ExpressLRS). Will not accept any conversation if you don't know MAVLink, so please do not contact me if you don't. - Knowledge in ESP32 and Ethernet, WiFi, BT - Arduino IDE with FreeRTOS - PX4 or other M...

...сделан на ESP32. Управление функциями осуществляется через web интерфейс. К контроллеру необходимо добавить управление платой DFPlayer по UART, управление должно быть добавлено в WEB интерфейс. Также требуется сделать контроллер RGB ленты (не адресной) на базе любой платы Arduino и управлять этим RGB контроллером также с WEB интерфейса контроллера мини бассейна. RGB контроллер будет подключен по I2C к контроллеру минибассейна. Исходный код прошивки и часть схемы контроллера мини бассейна будет предоставлена. Прошивка написана в ESP-IDF

Lopking for some expert embedded software engineer to understand the schimatic and program as per our needs

I am looking for a freelancer to help me develop an I2C to RS485 interface for the MODBUS RTU protocol. Microcontroller: No specific microcontroller has been chosen for this project, but I have a preferred microcontroller brand. However, I am open to suggestions from the freelancer. Noise Immunity: The project requires a high level of noise immunity to ensure reliable communication between the I2C and RS485 interfaces. Ideal Skills and Experience: - Proficiency in microcontroller programming and communication protocols (I2C, RS485, MODBUS RTU) - Knowledge and experience with various microcontroller brands and their capabilities - Familiarity with EEPROM usage and implementation - Expertise in designing circuits with high noise immunity - Ability to troubleshoot an...

...my existing VSCode PlatformIO project that requires the integration of this component. I am trying to use existing drivers for this device but run into too many time consuming errors. I intend to send my code to you and if you can guide me solving it, that would be great. Skills and Experience Needed: - Proficiency in C++ programming language VSCode and PlatformIO w. ESP32 - Strong knowledge of I2C communication protocol - Experience with drivers, adresses, .cpp and .h librairies etc. - Electronics engineering skills, understanding of schematics. If you have the necessary skills and experience, and are available to work on this project, please submit your proposal. My suggestion would be to pay per hour and perhaps cooperating by initially sharing the screen via Teams is also...

Experience in the authentication process of an inkjet cartridge (response and challenge) is a plus. We will provide, logic analyzer images. Proficiency in programming lan...process of an inkjet cartridge (response and challenge) is a plus. We will provide, logic analyzer images. Proficiency in programming languages such as C or C++ Strong knowledge in protocols like i2c, SPI, UART and iso7816 Ability to Emulate any EEPROMS using logic analyzers output Embedded firmware design(Attiny45,PIC16F877A). Excellent debugging skills. Job Type: Consultant Benefits: Flexible schedule Experience level: No experience needed Application Question(s): PLEASE ANSWER Are you able to emulate any EEPROMS using logic analyzers output? Are you able to analyze protocols like i2c, SPI, U...

I am looking for a firmware developer who can assist me with the development of a MODBUS I/O expander 16 channel using the Nuvoton MCU. The ideal candidate should have experience in embedded firmware development and be fa...Nuvoton MCU - Implementing the MODBUS communication protocol for seamless data exchange - Ensuring the firmware is reliable and efficient for embedded systems Skills and experience needed for this job: - Strong proficiency in firmware development using the Nuvoton MCU - In-depth knowledge of the MODBUS communication protocol - Experience in developing firmware for embedded systems - Familiarity with I2C and SPI communication protocols is a plus If you have the necessary skills and experience, please submit your proposal along with relevant samples of your prev...

...looking for a freelancer who can help me establish an I2C connection between an ICM20948 accelerometer and an STM32 microcontroller. Purpose of the I2C connection: - The main purpose of establishing this I2C connection is to enable communication with other devices. Type of ICM20948: - The ICM20948 used in this project is an accelerometer, gyroscope and magnetometer. Communication protocol: - The I2C communication protocol is used for this I2C connection. Ideal skills and experience: - Proficiency in STM32 programming and I2C communication protocol implementation - Experience with accelerometer sensors, specifically the ICM20948 - Knowledge of data logging and sensor fusion techniques - Ability to troubleshoot and debug I2C...

...Environment: - The transmitter should be able to withstand harsh outdoor conditions. Ideal Skills and Experience: - Experience in designing and implementing 4 channel, 2 wire 4-20ma transmitters. - Knowledge of industrial settings and the ability to design for harsh outdoor conditions. - Attention to detail to achieve the desired accuracy of 1%. I would prefer to implement this with an I2C signal from my PIC32 - but I am open to other suggestions (Note the project is a bit short of pins so using a pwm signal x 4 is not great - unless I add another small uC to interface between the PIC32 and the current transmitter. I am looking at the Max2900 part - but this needs ? 4 x PWM signals for control. The purpose of this project is to add 4-20ma loop control primarily of...

Proficiency in programming languages such as C or C++ Strong knowledge in protocols like i2c, SPI, UART and iso7816 Ability to Emulate any EEPROMS using logic analyzers output Embedded firmware design(Attiny45,PIC16F877A). Excellent debugging skills. Job Type: Consultant Benefits: Flexible schedule Experience level: No experience needed Application Question(s): PLEASE ANSWER Are you able to emulate any EEPROMS using logic analyzers output? Are you able to analyze protocols like i2c, SPI, UART and iso7816?

Hi Vijaygeeri G., I noticed your profile and would like to offer you my project. We can discuss any details over chat.

I have some I2C devices. All of them have same addresses on their I2C bus. (0x60) I want to connect 64 pcs of these I2C devices to a Raspberry Pi 4. 8 pcs will connect to TCA9548A I2C Multiplexer. And 8 different TCA9548A I2C Multiplexer will connect to another multiplexer. There is Remote-I2C library. I want to use this library or another. I want two different application. Server-Client. Server side is physically connected with master multiplexer. Server application serves I2C outputs according to incoming address resquests. Output should be always from 0x60 address of I2C bus final I2C device. Client side should be installed on a VMWare Linux. There is no normally I2C bus. You need to create (or simulate w...

Hi Please find the proposed work we will write a program to sent voltage through i2c and receive analog voltage through A0 of aurdino and sent through serial port. DAC (MCP4725) input voltage -0.1V to +0.1V with 10mV steps , so total 20 steps and time for 1 step to another is 0.4mSec.

The task is to help me build and create a project that will start with image ( toy car) clas...classification, then implement a video recognition of this object on Jetson Nano with a camera. The software should identify the object, and deliver the "find" with it's coordinates. Then few pins of the jetson nano external pins should toggle (e.g. turn a led on), and I2C message should be sent to an external device. After this stage the job is finished. The work requires good English communication skills, knowledge of image classification and recognition using Python, experience with Jetson Nano, interfacing with Jetson Nano pinout & I2C & MQTT. I think this can take only few hours for someone who has the right knowledge of all the parts. Experience wit...

Find fix to problem of "ETH not working on our Custom board using LPC1758 "based LPCExpresso LPC1769 board. Our board uses LPC1758, Initial rev boards worked all good. ( Even though  MIDO, MDC is funstion are not available on 1758) On Next revision boards ETH does not work. ( No change was done to schematic except fixing  SCL, SDA for I2C bus) Debug halts at following line; in void Chip_ENET_Init(LPC_ENET_T *pENET, bool useRMII) /* Initial MAC configuration for full duplex, 100Mbps, inter-frame gap use default values */ pENET-> = ENET_MAC1_PARF;

I am looking for a skilled freelancer to help me with adressing and running two stepper motors via an I2C bus on an Arduino. I just need a simple code to run motor 1 360degrees and after this motor 2 360 degrees. in my case i am using a PCF8574 I²C for Display LCD 16x2 witch in my opinion is the same as the i2c expander module. The motors are 28BYJ-48 with ULN2003 Driver PCF8574 address is 0x27 pls check the attached foto. The successful candidate will need expertise in working with I2C, Arduino, and stepper motors in order to successfully complete this project.

need to test basic examples of bme680, adc and other I2C sensor.

I am looking for a highly skilled STM chipset developer with experience in STM32 microcontrollers. This is an ongoing project that requires an immediate start with a fast turnaround. Requirements: - Experience with STM32 F4 microcon...software - Ability to work on an ongoing project with tight deadlines - Strong problem-solving skills and attention to detail - Good english communication Ideal Skills and Experience: - Proficiency in programming languages such as C and C++ - Knowledge of embedded systems and hardware design - Experience with firmware development and debugging - Understanding of communication protocols such as I2C, SPI, and UART If you have the expertise and availability to take on this project, please submit your proposal with relevant experience and examples of ...

Hello, I am currently seeking someone who is interested in taking on a project involving the implementation of STM32h750. The project consists of integrating an SD card and dual DMA for audio streaming, specifically with a dummy buffer. Additionally, there is an option t...I am currently seeking someone who is interested in taking on a project involving the implementation of STM32h750. The project consists of integrating an SD card and dual DMA for audio streaming, specifically with a dummy buffer. Additionally, there is an option to handle the entire project, which includes retrieving data from an external ADC (as a master, without the need for configuration via I2C) and storing it onto the SD card using dual DMA. If you are interested in this project, please let me know. ...

I am ...design and be able to provide consultation on circuit design. Additionally, knowledge of single-sided and double-sided PCB technology is preferred. The project consists of designing a pcb board which contains proximity sensor and count display. in the code we trigger the IR emitter and look at the status of IR receiver. each pcb has a slave PIC microcontroller. all the slaves are controlled via I2C bus by a master. the master receives data from each slave about the number of coins on each line. it then adds up the whole amount. On a press of a button the master switches the screens to display the aggregate sum the master also communicates via a RS232 bus to a PC to dispaly tray status on a local react app running on PC the re232 commands are simple amd are defined in ...

I am looking for a freelancer to design and develop - Enhance / modify current design of our Raspberry Pi I/O Extender board. -- Adding into it a 'daisy chain feature for the daughter boards(see below). - Design 'daughter' / 'child' boards which can be hooked up in a chain talking over I2C, SP2 etc Function: - Daisy Chain / Connect through RJ45 Cables / headers. (Data and low power) - Have a high power input / output for motor. (opto isloated) - Input pins, and output pins. - Dip switch block for 'position' in node chain / daisy chain. - OLED screen for displaying basic Info(2.42 inch) - Control string of WS2812 LED's OLED screen will simply displays 0-999. and basic connection / startup / config options. The idea is relatively simple. ...

...to main raspberry pi board. - Running total of all 8 machines should be sent back to 'gathered' on main raspberry pi board/breakout board. - When running total on main board hits 999 then or counter from nodes/satellites hits 999 then a MOTOR is triggered from main Raspberry Pi board. Interface: - I2C Form Factor: - Custom size Ideal Skills and Experience: - Experience in designing and developing Raspberry Pi modules - Proficient in programming languages such as Python - Knowledge in I2C interface and circuit design - Familiarity with custom hardware design and manufacturing The project will involve designing the circuit and PCB layout, programming and testing the module, and producing a prototype. The successful candidate will be able to deliver a high-q...

I am looking for an experienced freelancer who can help me with my project titled "Bluetooth Device to read data from Sensor via I2C". The project requires the following skills and experience: - Familiarity with Bluetooth technology and its protocols - Experience in developing Bluetooth devices to read data from sensors via I2C - Ability to work with the specific Bluetooth device that I have in mind - Experience in developing short-range Bluetooth connections (up to 10 meters) The project entails developing a Bluetooth device that can read data from an Air Quality Sensor via I2C. The device should be able to establish a short-range Bluetooth connection of up to 10 meters. I have a specific Bluetooth device in mind that I would like the freelancer to work wi...

I am looking for an experienced Arduino developer to help me generalize my i2c code. I am using a specific Arduino board, which I will specify. I have some code that actually manages 16 i2c OLED screens using 2 i2c muxes, but want to code a program that manages the 8 possible muxes by address. The code receives some midi sysex signals (screen number, text), and sends it to the corresponding screen. So in summary I want to convert the code supporting 2 muxes into a generalized one for 8 muxes, stored into an array of references, and tidy up the code in general. The original code will be shared accordingly.

DESCRIPTION: "Cyclops": framework ...(language & IDE) for BeagleBone Black microcontroller/development board -current functions are present in the "/Cyclops-PRU/C lib/include" folder - some are listed in TABLE I on the 4th page of the "" file I am attaching GITHUB REPOSITORY LINK: TASK: 1) Develop further API functions for the language - to be programmed in C; (some ides: File Access, i2c, Memory Management, Power Management UART, Communication Protocols such as for Bluetooth and Wi-Fi, Timers, PWM etc.) 2) To test the functions you built, write examples like the ones in "/Cyclops-PRU/C lib/examples", and compile them in the IDE; 3) Write a document describing all the API functions added, their functionalities, and explaining the ex...

DESCRIPTION: "Cyclops": framework ...(language & IDE) for BeagleBone Black microcontroller/development board -current functions are present in the "/Cyclops-PRU/C lib/include" folder - some are listed in TABLE I on the 4th page of the "" file I am attaching GITHUB REPOSITORY LINK: TASK: 1) Develop further API functions for the language - to be programmed in C; (some ides: File Access, i2c, Memory Management, Power Management UART, Communication Protocols such as for Bluetooth and Wi-Fi, Timers, PWM etc.) 2) To test the functions you built, write examples like the ones in "/Cyclops-PRU/C lib/examples", and compile them in the IDE; 3) Write a document describing all the API functions added, their functionalities, and explaining the ex...

ESP Master/Valve Driver Update: 1. Replace the 5v LDO to Buck converter. So we can provide 12v input power supply and convert it to 5v for ICs 2. W...4-Valve/8-Valve board. 4. May need to revisit the power draw of LEDs in master board 5. Sometimes ESP overheats with WiFi STA/AP mode. 6. Redesign existing Eagle project into Easy EDA 7. Provide adequate support for Firmware changes Slave/Wireless Pump Controller: 1. Handle ESP32 brownout/flicer scenarios when WiFi is turned On and sending HTTP request to master 2. Remove the 5V power supply to I2C FRC Connector. We may not need this anymore 3. Battery IC Overheating. Guess you suggested to change the resitor. 4. Replace unused sensor port with 12v Power rail. So we can connect Pressure sesnsor with I/P 10-30V and current outp...

Looking for collaboration from some good responsible, honest, serious software talent. We assume you have plumbing experience on SW development for FF H1 bus. We need a FF H1 interface code on RPi 3 talking via I2C/SPI to a TI DAC8742H. ...

My device has esp32 processor, simcom A7672E gsm module. In addition, there are 8 digital inputs made using 74hc165, 8 digital outputs made using 74hc595, 3 analog inputs, 2 analog outputs, 1 rs485 port, 128x64 oled display working with I2C. The system is exchanging data with http query. Processing the Modbus Tcp/Ip queries that will come from the gsm module, which has a fixed-ip sim card, over the uart, in transparent mode, on the inputs and outputs on the desired, and giving the necessary response.

It needs network, control of DSP chips via I2C, presets, and UART and bootloader and firmware update process. We have the code for Freescale chip in C, and it works perfectly but code needs to be moved to STM. Please apply if you are experienced and confident.

...Update graphic interface Add iOs compatibility and Android version Add external NFC reader compatibility (type ACR122U) Add diagnostic function (memory full export and API with external server) Add last data visualisation and export (nfc record display + memory export to external server) Add reconfiguration of new product range (nfc record read / write / modify) Add FUOTA feature via NFC (NTAG I2C pass through mode) We will provide : Full functionnal specification of the project Source code of the existing application Technical requirements Test and validation environnement (products) Technology to be used :  React Native State manager : Can be proposed but something like Jotai / Redux Deliverables :  Full files including : source code and project before ejecting ...

...will control up to 4 relays handling 24V AC / 1A max. Key requirements: ESP32-WROVER-E-N8R8 module with program and reset buttons, as well as status LEDs for upload and operation. Four relays capable of handling NO - COM 24 Volts AC / 1 Amp max. (pins defined by designer) Rectifier bridge to convert 24V AC input to 12V DC / 3.3V DC. Temperature and humidity sensor: Sensirion I2C SHT31-DIS-B2.5kS. VOC sensor: Sensirion I2C SGP40-D-R4 (with a different address on the same bus). SMD components and a rectangular PCB no larger than 60x60mm. Ethernet interface with port( preferebly use LAN8720) have an Waveshare 2.13inch E-Ink Display Module connected to the ESP32 Deliverables: Schematic and PCB layout files in Eagle or another industry-standard format. BOM with Digi-Key par...

I need to make a change to this code removing this sensor Adafruit STEMMA Soil Sensor - I2C Capacitive Moisture Sensor and adding this Generic Capacitive Moisture Sensor v1.2

Looking for collaboration from some good responsible, honest, serious software talent. We assume you have plumbing experience on SW development for FF H1 bus. We need a FF H1 interface code on RPi 3 talking via I2C/SPI to a TI DAC8742H. ...